Land Raider Ares

[Darios]

q silvius: kommst du öfter ins emp? weil wenn ja könnte man mal zocken...

 

[Lexandro Arquebus]

Verwechselst du gerade vielleicht die Zwillingsmaschinenkanone der Chaos Space Marine Terminatoren mit der loyalen Sturmkanone???

Synch. StuKa des LRC nach Codex Black Templar: 24", S6, DS4...

 

[JaqTaar]

Hab gerade nochmal nachgeguckt: Auf der engl. GW-Seite ist im Apocalypse-Bereich nicht nur das Datenblatt noch immer zu finden, sondern auch eine Beschreibung des Umbaus.
http://www.games-workshop.com/gws/c...egoryId=900006&pIndex=10&aId=6700007&start=11
Kann sein, dass der Artikel erst erscheint nachdem man ein Land ausgewählt hat. Ansonsten hier der relevante Teil:

What really made this project work is that the the front hull piece on the Vindicator sprue fits very nicely on the front of the Land Raider with just a little bit of modification. I cut down the Assault ramp so that it would fill in the area below the hull. I also put the blast exhaust fan from the Vindicator on the back top of the Land Raider, this took a bit of cutting but ended up fitting nicely as well.

Next I decided to extend the dozer blade so that it would look wide enough to fit on the front of a Land Raider. Since the dozer blade that comes with the Vindicator is in three pieces this made it very easy to cut a couple pieces of plastic card the same thickness as the dozer blade and extend the sides a bit. Do a bit of dry fitting before you start gluing just to make sure it all fits right. I then attached the dozer blade with the dozer hydraulics provided on the Vindicator sprue. I decided to connect the dozer blade to the assault ramp section of the Land Raider rather then the sides as it is on the Vindicator, however you could do it either way. You might consider gluing the Dozer Blade to the mounts after you have painted the model as that will make it easier to paint the front section.

Lastly I had to work out what I wanted use on the side sponsons. Originally I built twin-linked Multi-melta sponsons with the idea that they would be a back up for the Demolisher cannon if it was ever destroyed. But this seemed way over powered and didn't quite fit with the siege assault role I had wanted for this tank. So I decided to go with Twin-linked Heavy flamers. (Yes you read that right, Twin-linked flamers check out the rules for Twin-linked template weapons on page 31 of the 40k rule-book) In my mind I could picture the Ares blowing a hole in a fortification and the enemy pouring from the hold only to be greeted by cleansing flame and Assault cannon rounds. I used the Baal Predator Heavy flamer Sponsons which fit with just a little modification to the center support piece. If you trim off the Blood Angels symbol on the side of the Heavy Flamer sponsons the Land Raider sponson covers fit over them as well.

 

[Captain Silvius]

Zitat von Lexandro Arquebus:
Synch. StuKa des LRC nach Codex Black Templar: 24", S6, DS4...

sorry, aber das ist klar, das der LRC dieselben Sturmkanonen hat wie die normalen Termis / Cybots auch

:blink:

es ging ja bei mir um den vergleich -> Chaos Vorgänger vs. loyaler Nachfolger (Zwillings-Maschinenkanone vs. Sturmkanone).

P.S.: Bei dir "Lexandro Arquebus" fehlt noch der absatz im Zitat, das Transporter der BT nur die Trupps aufnehemen können, zu welchem Trupp sie gekauft wurden 😉. Dies gilt auch für die noch aktuellen Imps (engl. FAQ von GW).

 

[Fallout_Boy]

Halls jemand mit dem Gedanken spielt sich so ein Monstrum zu bauen, ich habe noch ein Demolisher geschütz aus Zinn von einem alten Vindikator herumliegen.